Graco SuperCat 232721 Скачать руководство пользователя страница 67

Страница: 67 / 114

308925

Troubleshooting

Premier Pump

Problem

Operating Condition

Cause/Solution

Pump does not cycle, no fluid
pressure developed

In manual mode, Premier pump key
held down, schematic Premier pump
light on

Check pump air regulator setting.

Make sure pump air ball valve is
open.

Check Premier pump air solenoid.
See page 72.

In manual mode, Premier pump key
held down, schematic Premier pump
light off

Check keypad continuity. See page
75.

Replace circuit board. See

Service

on page 87.

In spray mode, schematic Premier
pump light on

Check pump air regulator setting.

Make sure pump air ball valve is
open.

Check Premier pump air solenoid.
See page 72.

Pump does not cycle, fluid pres-
sure developed

In spray or manual mode

Plugged gun spray tip. Clean spray
tip as instructed in gun manual.

Check valve positions against posi-
tions shown in Operation Manual
308875 for current operation.

Plugged high pressure fluid filters.
Clean filters. See

Service,

page 77.

Pump cycles when gun is not
triggered

In spray mode

Check valve positions against posi-
tions shown in Operation Manual
308875 for current operation.

Air in fluid lines. Purge air.

Leaky ball valve. Replace valve.

Reservoir ball valve closed. Open ball
valve.

Pump lower failed. Service lower.

Mix manifold failed. Service manifold.

Pump runs too fast

In manual or spray mode

Check valve positions against posi-
tions shown in Operation Manual
308875 for current operation.

Decrease air regulator pressure set-
ting.

Pump lower failed. Service lower.

Pump does not stop

In manual or spray mode, schematic
Premier pump light off

Check Premier pump air solenoid.
See page 72.

Output pressure is low or pump
dives on the upstroke

In manual or spray mode

Service pump.

Output pressure is low or pump
dives on downstroke

In manual or spray mode

Service pump.

Material usage display value does
not change

In manual or spray mode

See material usage display trouble-
shooting.

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды