Graco SuperCat 232721 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 114

background image

308925

16

Installation

4.

Optional: Install the feed pumps and
the 240689 Feed Pump Control Kit.

NOTE:

The 240689 Feed Pump Control Kit is

factory installed on heated proportioners 232713
through 232724. The kit includes necessary parts
to install two air regulators and dolenoids to control
the feed pumps. Refer to manual 308959 for
installation instructions.

It is recommended that the feed pumps have twice
the flow rate of the Premier production flow rate (2
GPM, 7.6 liters/min. maximum). Undersized feed
pumps can cause an alarm or cause the reservoirs
to run dry.

NOTE:

Additional sensors can be purchased to

allow the control to monitor both the full and low
fluid levels.

5.

Optional: Install the 240690 Level Sen-
sor Kit

The optional 240690 Level Sensor Kit includes two
level sensors, to add to the two supplied with the
proportioner. The installation of both low and full
level sensors, along with the change of the level
sensor option in setup, allows the system to be
used with manual or automatic feed with feed
pumps, without changing the sensor locations.

Refer to manual 308860 for installation instruc-
tions.

6.

Optional: Install 240688 Low Pressure
Sensor Kit

This optional kit includes two low pressure sen-
sors, which attach to the reservoir outlet filters
(54). The low pressure sensors, along with a
change in setup, enable the system to detect a
plugged filter and sound an alarm.

Refer to manual 308861 for installation instruc-
tions.

«
...
14
15
16
17
18
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: PANDROL Страницы: 36

Бренд: Cadex Страницы: 300

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: Palmer Страницы: 2

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: Yamaha Страницы: 29

WELCH LVS 600 T

Бренд: Gardner Denver Страницы: 68

Бренд: Osram Страницы: 4

Бренд: Kongsberg Страницы: 188

Бренд: Proactive Страницы: 14

Бренд: sauter Страницы: 5

Life/form LF03608

Бренд: Nasco Healthcare Страницы: 6

Бренд: Beta Страницы: 8

Бренд: Jaeger Страницы: 36

Бренд: ParaBody Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды