Graco SuperCat 232721 Скачать руководство пользователя страница 9

Страница: 9 / 114

308925

Component Identification

KEY

Premier

Proportioning Pump

15*

Reservoir

Mix Manifold

17c Static Mixer
20

Air Lubricator

39*

Gun Fluid Hose, 50 ft. (15.25 m), 3/8 in. (9.53 mm) (not shown)

41*

Gun Whip Hose, 6 ft (1.83 m)., 1/4 in. (6.35 mm)

42*

Graco Silver Plus

Spray Gun

Standard 3 Gun Manifold (out of view behind reservoir)

53*

Agitator

54*

Reservoir Filter

56*

Reservoir Ball Valve

Premier Pump Air Shutoff Valve

89*

President

Solvent Pump (out of view behind cabinet)

121 Main Air Shutoff Valve
125e System Schematic Panel

125g Keypad with Display
202 Fluid Filter
203 Automatic Pressure Relief Valve
204 Fluid Drain Valve
207 Fluid Outlet Pressure Gauges
506

Fluid Heater

508

Insulated Fluid Hose (shown)

Premier Air Regulator

Solvent Air Regulator

Feed Pump A Air Regulator (optional)

Feed Pump B Air Regulator (optional)

* These items are not included in the Basic Packages.

These items are only included in the Heated Packages.

8788A

Fig. 1

121

89*

15*

56*

54*

53*

17c

204

202

203

125e

125g

42*

508

(shown) or39*

41*

207

506

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды