Graco SuperCat 232721 Скачать руководство пользователя страница 6

Страница: 6 / 114

308925

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INJECTION HAZARD

Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin
can also cause serious injury.

Fluid injected into the skin might look like just a cut, but it is a serious injury.

Get immediate medi-

cal attention.

Do not point the spray gun at anyone or at any part of the body.

Do not put your hand or fingers over the spray tip.

Do not stop or deflect leaks with your hand, body, glove, or rag.

Do not “blow back” fluid; this is not an air spray system.

Check the gun diffuser operation weekly. Refer to the gun manual.

Always have the tip guard and trigger guard on the spray gun when spraying.

Check the gun diffuser operation weekly. Refer to the gun manual.

Be sure the gun trigger safety operates before spraying.

Lock the gun trigger safety when you stop spraying.

Follow the

Pressure Relief Procedure

on page 21 if the spray tip/nozzle clogs and whenever you:

are instructed to relieve pressure; stop spraying; clean, check, or service the equipment; and install
or clean the spray tip.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily. Do not mend or repair any part of the hose assembly.
If the hose is damaged, replace it immediately.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate fingers.

Do not operate the equipment with the air motor plates removed.

Keep your body and tools clear of any moving parts when starting or operating the equipment.

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды