Graco SuperCat 232721 Скачать руководство пользователя страница 69

Страница: 69 / 114

308925

Troubleshooting

WARNING

INJECTION HAZARD

This system can produce very high fluid
pressure. To reduce the risk of a serious
injury:

Follow the

Pressure Relief Procedure

on page

21 before checking or servicing the equipment.

Use very low air pressure to operate the pump
when troubleshooting.

WARNING

MOVING PARTS HAZARD

To reduce the risk of injuring or amputat-
ing hands, fingers, or other body parts,
never place your hands, body or tools
inside the safety panels while the unit is
operating.

Pump Lowers

Because the pumps are mechanically linked, the action
of one pump can affect the readings of the second
pump. Therefore, the key to successful troubleshooting
is to isolate the problem.

For example: if the secondary pump pressure gauge
reading is low and sluggish during the pump change-
over, the most likely problem is a binding primary
pump. To isolate the problem:

Isolating the Primary Pump

Follow the

Pressure Relief Procedure

on page

21.

Open the fluid drain valves (204).

Set the Premier pump air regulator (C) to the
lowest setting and make sure the pump air valve is
open.

Press and hold the Premier pump key (PK).
Increase the air regulator (C) setting until the pump
just begins to move. Notice the position of the

secondary pump (312

). Release the Premier

pump key so that the secondary pump rod is at its
lowest position when the pump stops.

With the main air valve closed, remove the screws
(469) and guard (424) from the side of the propor-
tioner.

Unscrew the connecting rod nut (361) from the

secondary pump (312

). Now you can verify the

operation of the primary pump (311

) alone.

Reinstall the guard (424) on the proportioner.

Turn on the main air valve, press the Premier
pump key (PK), and carefully increase the Premier
pump air pressure.

Open and close the fluid drain valves (204) and
check for pump stalling on both the up and down
strokes.

10. Check for rapid gauge (207) response during the

pump changeover.

11. When the operation of the isolated pump has been

verified, turn the Premier pump air regulator setting
to zero and follow the

Pressure Relief Proce-

dure

12. Turn off the main air valve.

13. Reconnect the pump connecting rod nut (361).

Isolating the Secondary Pump

14. With the fluid drain valves (204) still open, set the

Premier pump air regulator (C) to the lowest
setting and open the main air valve.

15. Press and hold the Premier pump key (PK).

Increase the air regulator (C) setting until the pump
just begins to move. Notice the position of the

primary pump (311

). Release the Premier pump

key so that the primary pump rod is at its lowest
position when the pump stops.

16. With the main air valve closed, remove the screws

(469) and guards (446) from the side of the propor-
tioner.

17. Unscrew the connecting rod nut (361) from the

primary pump (311

18. Now you can verify the operation of the secondary

pump alone. Follow steps 7–13, above.

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды