Graco SuperCat 232721 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 114

background image

308925

10

Installation

General Information

Reference numbers and letters in parentheses in
this text refer to the numbers and letters in the
illustrations.

Be sure all accessories are adequately sized and
pressure-rated to meet the system requirements.

See page 112 for dimensions.

Apply

tape and sealant to pipe threads

before assembling them. Leave the first thread
uncovered to maintain electrical continuity.

Notes About Basic Units

The basic units require pressure–fed systems for
each material (A and B). Do not exceed 1000 psi (7
MPa, 70 bar), and make sure the feed system is
capable of at least twice the volume of the pump it
is supplying.

If heat is used on the feed systems, make sure the
fluid hose is capable of the heat and pressure
required. Mount the heaters on the heater bracket
as described on the following pages, making sure
they are appropriately plumbed for constant fluid
flow. Since reservoirs are not used, the circulation
feature is not available, and provisions should be
made to circulate material back to the feed source
during non–operational periods.

Make sure the basic units do not have features
operable that relate to the sensors on the reser-
voirs. Check the feature and its setup to ensure its
action is not related to reservoir sensors. This could
cause nuisance alarms.

Keep the Component Fluid Paths
Separate

CAUTION

Be sure to label all fluid path parts “component A” or
“component B”. Doing so prevents interchanging A
and B parts, which will contaminate the materials and
the fluid path through the equipment.

Color-coded chemically resistant tape may be used
to label the parts. Use Part No. 070540 blue for
component A, 070541 green for component B,
070542 red for mixed material, and 070543 white for
solvent.

Moving the Proportioner

WARNING

To avoid serious injury, do not lift the
equipment by the Premier air motor lift
ring (H–Fig. 2). It cannot support the
weight of the system.

8792A

Fig. 2

H

If moving the proportioner with a forklift, be sure it is
securely set on the forklift before lifting it.

If moving the proportioner with a crane, the propor-
tioner must be placed in a cage or other sturdy sup-
port, which fully supports the base/pallet.

Do not

attach the crane hook to the Premier air motor lift
ring, or any other part of the proportioner system!

PTFE

PTFE

PTFE

«
...
8
9
10
11
12
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Navman Страницы: 17

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Macht Dental Страницы: 8

Бренд: OHAUS Страницы: 84

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

Бренд: York Страницы: 16

i.Profiler plus

Бренд: Zeiss Страницы: 66

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

Бренд: Posture Pump Страницы: 2

Бренд: Yacht Devices Страницы: 32

Бренд: GE Страницы: 241

Бренд: GE Страницы: 223

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды