Graco SuperCat 232721 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 114

background image

308925

78

Care of the System

Clean the Static Mixer

Visually inspect the static mixer (G)

weekly

. Replace

the static mixer if clogged or damaged.

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Remove the hose (35) from the static mixer (G).

3.

Unscrew the static mixer (G) from the mix manifold
(17).

4.

Push the mixer element out of the static mixer by
inserting a wooden dowel at the adapter (H) end.
Clean all parts with a compatible solvent, and
reassemble.

5.

Install the static mixer (G). The arrow on the static
mixer must point down. Apply tape and sealant to
the threads of the static mixer.

Fig. 97

1

2

8344A–part

35

H

G

17

Arrow must point down.

Apply tape and sealant to threads.

1

2

Care of the Premier Pump Throat Packing
Nut/Wet Cup

The throat packing nut/wet cup (J) should be inspected
and filled on a weekly basis, or more frequently if
found to be dry. See Fig. 98.

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Turn off the main air valve.

3.

Remove the screws (469) and the two guards
(424, 446) from the sides of the proportioner. See
Fig. 99.

4.

The wet cups should be 1/3 full of Graco Throat
Seal Liquid (TSL) or compatible solvent.

5.

The packing nuts are torqued at the factory and
are ready for operation. Check the tightness of the
packing nut weekly. If it becomes loose and there
is leaking from the throat packings:

a.

Follow the

Pressure Relief Procedure

on

page 21, before adjusting the packing nut.

b.

Tighten the packing nut to the torque for your
lower model, using the wrench supplied. See
the table below. Do not over-tighten the pack-
ing nut. Too tight an adjustment causes the
packings to bind or wear prematurely and leak.

Pump Lower

Packing Nut Torque

Dura-Flo 600 (236458)

45–55 ft-lb (61-75 N

m)

Dura-Flo 900 (236470)

100–110 ft-lb (136-149 N

m)

Dura-Flo 1200 (237514)

100–110 ft-lb (136-149 N

m)

J

1

Fig. 98

04373

1

See torque requirements, above.

«
...
76
77
78
79
80
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Falcon Страницы: 52

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: Keithley Страницы: 42

Бренд: fadini Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: Pari Страницы: 282

Бренд: V.ORLANDI Страницы: 144

Бренд: Sable Страницы: 28

Бренд: Daikin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды