Graco SuperCat 232721 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 114

background image

308925

17

Installation

7.

Optional:

Remove and relocate the mix

manifold.

It may be necessary to move the mix manifold (17)
closer to the object being sprayed to reduce the
length of mixed material fluid hose. This will help
reduce material waste and may be necessary
when using materials with very short work life.

NOTE:

Work life time

is the amount of time that a

material can be effectively sprayed and applied to
a surface.

To remove the mix manifold from the proportioner,
disconnect the fluid lines from the mix manifold
fluid line connectors (17d). Loosen the knob (58)
and lift the panel (16) off the unit. Place the mix
manifold in the location desired. Make sure the
mounting surface can support the weight of the
manifold, any hoses connected to it, and any
stress that may be applied during operation.

Connect the fluid lines, in the length required,
between the proportioner and the mix manifold. If
using more than 50 ft. (15.25 m) of hose between
the pump and the mix manifold, contact your
distributor for the recommended hose diameter for
the best ratio assurance.

Do not exceed a maximum of 300 feet (91.5 m) of
total hose length.

8.

Optional: Connect additional guns.

The standard proportioner has a three gun man-
ifold (44). See Fig. 10. Two of the 3/8 npt outlet
ports are plugged. The gun fluid hose (provided) is
connected to the bottom port.

WARNING

COMPONENT RUPTURE HAZARD
Do not

install a fluid shutoff device

between the heater and the gun.

To connect additional guns, remove the plug(s)
(37) and install shut-off valve(s) (SV) on non-
heated systems only. Then install the fluid hose(s)
and gun(s). Add a shut-off valve to the gun fluid
hose that is included with the proportioner.

NOTE:

Install hoses and guns in the lowest avail-

able manifold port to prevent mixed material from
solidifying in an unused area of the manifold.

Fig. 9

58

16

17

KEY

16

Panel

17

Mix Manifold

17a Mix Manifold Shutoff

Valve

17b Solvent Shutoff Valve
17c Static Mixer
17d Fluid Line Connector
58

Knob

17a

17b

17d

17c

8352A

8397A

Fig. 10

44

37

SV

1

Do not install on heated systems.
See the WARNING at left.

1

«
...
15
16
17
18
19
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: NORLUX Страницы: 2

Бренд: C.M.O Страницы: 10

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды