Graco SuperCat 232721 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 114

background image

308925

93

Service

Replacing the Sensors (continued)

Solvent Pump Cycle Counter

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Disconnect the cycle counter sensor (607) from its
mating connector. Unscrew the cycle counter
sensor housing (622) from the air motor port. See
Fig. 113.

3.

Install the new sensor housing and sensor.

4.

Connect the sensor to the correctly labeled mating
connector.

Fig. 113

8345A–part

607

622

Proportioning Pump Cycle Counter

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Disconnect the cycle counter sensor (465) from its
mating connector. Unscrew the four screws (458)
and remove the back pump cover (406). See Fig.
114.

3.

Remove the screws (469) and the guard (446)
from the side of the proportioner.

4.

Remove the jam nut from the sensor (465).

5.

Remove the sensor from the pump frame.

6.

Install the new sensor and jam nut.

7.

Connect the sensor to the correctly labeled mating
connector.

8.

Replace the back cover (406) and the screws
(458).

9.

Replace the guard (446) and screws (469).

Fig. 114

8414A

465

458

406

469

446

«
...
91
92
93
94
95
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Keithley Страницы: 149

Бренд: Panasonic Страницы: 30

Бренд: Jackco Страницы: 6

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: Jacobsen Страницы: 20

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Nel-Tech Labs Страницы: 8

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

Бренд: Panasonic Страницы: 23

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренд: Nahita Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды