Graco SuperCat 232721 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 114

background image

308925

7

WARNING

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD

Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and
result in fire, explosion, electric shock, or other serious injury.

Ground the equipment and the object being sprayed. See

Ground the Equipment

on page 18.

The heaters are grounded through the electrical power supply.

The electric heater must be installed, operated, and serviced only by trained, qualified personnel
who fully understand the requirements stated in the heater instruction manual.

All electrical wiring must be done by trained and qualified personnel and comply with all local codes
and regulations.

If there is any static sparking while using the equipment,

stop spraying immediately

. Identify and

correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.

Do not smoke within the spray area.

Extinguish all the open flames or pilot lights within the spray area.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all the equipment within the spray area.

Do not turn on or off any light switch within the spray area while operating or if fumes are present.

Do not operate a gasoline engine within the spray area.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state, and national guidelines.

Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and
solvent manufacturer.

Graco does not manufacture or supply any of the reactive chemical components that may be used
in this equipment and is not responsible for their effects. Graco assumes no responsibility for loss,
damage, expense, or claims for personal injury or property damage, direct or consequential, arising
from the use of such chemical components.

«
...
5
6
7
8
9
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: FENDT Страницы: 31

Бренд: HAMAR LASER Страницы: 49

Бренд: Cadex Страницы: 300

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Raytec Страницы: 60

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: UMS Страницы: 92

Бренд: Wasp Страницы: 50

Бренд: ABB Страницы: 33

Бренд: Petzl Страницы: 15

Бренд: Kettler Страницы: 20

Бренд: Omcan Страницы: 16

ZiXpress 64 DX system

Бренд: ZINEXTS Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды