Graco SuperCat 232721 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 114

background image

308925

11

Installation

1. Connect the main air line.

NOTE:

See Fig. 1 for all installation steps except

where otherwise directed.

Connect the main air line to the 1 in. npsm(f) inlet
of the air line filter (79) at the back of the cabinet.
See Fig. 3.

The air supply at the proportioner must be a mini-
mum of 100 psi (0.7 MPa, 7 bar) and 150 scfm
(4.2 m

3

/min.).

A minimum 1 in. (25.4 mm) I.D. hose is recom-
mended.

8806A

Fig. 3

79

Main Air Line

2.

Optional: Install 241157 Heater Kit

NOTE:

Packages 232713 through 232724 are

shipped with the 241157 Heater Kit and two Viscon
HP Fluid Heaters installed.

Kit No. 241157 is available to convert an unheated
SuperCat proportioner to the standard heated
system described on page 12. The kit includes
necessary parts to install two Viscon HP

fluid

heaters on the SuperCat. Refer to manual 308914
for installation instructions.

Viscon HP heaters and feed pumps are not in-
cluded with the kit and must be ordered separately.
The heaters are available in four voltages. Specify
which voltage you desire.

Model 245863 Viscon HP Heater
(240 V, single-phase, 16.7 A)

Model 245864 Viscon HP Heater
(480 V, single-phase, 8.30 A)

Model 245862 Viscon HP Heater (Asia)
(200 V, single-phase, 20.0 A)

WARNING

FIRE, EXPLOSION, AND ELECTRIC
SHOCK HAZARD

The Viscon HP Heaters must be
installed by a qualified electrician in
compliance with all state and local codes
and regulations, to reduce the risk of
electric shock or other serious injury
during installation or operation.

When installing in a flammable atmo-
sphere (hazardous location) refer to

Article 500 of the US National Electric Code or
other applicable agency standards to plan the
work.

Refer to the Viscon HP Heater manual (supplied
with the heater) for information on heater power
supply requirements.

Do not

plug in or unplug a power cord in any area

containing flammable fluids or fumes, to avoid fire
or explosion resulting in serious injury.

Do not

put flammable materials and debris on or

near the heaters. Keep the work area clean.

WARNING

COMPONENT RUPTURE HAZARD

Heat causes fluid to expand. If the
heated fluid is trapped with nowhere to
expand, it can cause component rupture.

Be sure

to keep the heated fluid circulating (open

the recirculation valves).

Do not

install a fluid

shutoff device between the heater and the gun.

«
...
9
10
11
12
13
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: C.M.O Страницы: 10

Бренд: Haigh Страницы: 60

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: S&C Страницы: 27

Бренд: S&C Страницы: 56

IntelliRupter PulseCloser

Бренд: S&C Страницы: 16

Бренд: S&C Страницы: 76

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

Бренд: Kärcher Страницы: 20

Бренд: Parker Research Corp Страницы: 3

Бренд: ABB Страницы: 33

Optima XR200amx

Бренд: GE Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды