Graco SuperCat 232721 Скачать руководство пользователя страница 113

Страница: 113 / 114

308925

113

Technical Data

Maximum working fluid pressure . . . . . . . . . . . .

5000 psi (35 MPa, 345 bar)

Maximum solvent supply pressure . . . . . . . . . .

4600 psi (32 MPa, 317 bar)

Maximum air input pressure . . . . . . . . . . . . . . .

100 psi (0.7 MPa, 7 bar)

Air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80–100 psi (0.5–0.7 MPa, 5.5–7 bar).

Air consumption (with President feed pumps)

150 scfm (4.2 m

/min.)

Mixing ratio range . . . . . . . . . . . . . . . . . . . . . . . .

2:1, 3:1, or 4:1 Fixed Ratio, depending on model

Fluids handled . . . . . . . . . . . . . . . . . . . . . . . . . . .

Two-component epoxy paints, solvent borne epoxies, waterborne
epoxies, primers, tank linings, fire retardants, anti-foulants

Fluid filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60 mesh minimum

Fluid flow at 20 cycles per minute . . . . . . . . . . .

2:1 ratio (232096): 2.3 gpm (8.7 liters/min.)
3:1 ratio (232097): 1.75 gpm (6.6 liters/min.)
4:1 ratio (232098): 2.2 gpm (8.3 liters/min.)

Operating temperature range . . . . . . . . . . . . . .

62 to 120

F (16 to 49

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

approximately 1350 lb (612 kg)

Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Premier proportioning pump:

304, 440, and 17–4 PH stainless

steel, Tungsten carbide,

, leather

President solvent pump:

303, 316, 440C, and 17–4 PH stainless

steel, tungsten carbide,

Reservoirs:

304 & 316 Stainless steel

Fluid filters:

303, 304, 313, and 316 stainless steel,

polyethylene

Mix manifold:

17–4 PH, 304 & 316 Stainless steel, tungsten

carbide,

, Delrin

, PEEK

Static mixer:

304 & 316 Stainless steel

Proportioner supply hose:

, 316 Stainless steel couplings

Fluid supply hose:

Nylon, 304 (or 316) Stainless steel couplings

Airless spray gun:

Stainless steel, polyethylene, polyurethane,

nylon,

Sound data

ormal operating conditions, Premier at 25

cpm/70 psi (480 kPa, 4.8 bar)

Sound pressure level . . . . . . . . . . . . . . . . . .
Sound power level . . . . . . . . . . . . . . . . . . . .

83.1 dBa
93.1 dBa

Maximum operating conditions, Premier at 60
cpm/90 psi (620 kPa, 6.2 bar)

Sound pressure level . . . . . . . . . . . . . . . . . .
Sound power level . . . . . . . . . . . . . . . . . . . .

88.6 dBa
98.8 dBa

NOTE:

See the individual component manuals listed on page 80 for additional technical data.

* Dependent on application. For more detailed information on viscosities, flow rates, or mixing ratios, consult your Graco distrib-

utor.

Sound levels include both agitators. Tested per ISO 3744–1981

and Delrin

are

registered trademarks of the DuPont Company.

PTFE

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды