Graco SuperCat 232721 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 114

background image

308925

74

Troubleshooting

Electronic Control Check

Problem

Operating Condition

Cause/Solution

Keypad display and schematic
blank

Open system air supply (red handle
ball valve). Check air supply pressure
and volume.

Clean main air filter.

Clean power supply filter.

Replace power supply. See

Service

on page 94.

Keypad fails continuity checks.

Replace keypad. See

Service

on

page 87.

Schematic lights fail continuity
checks.

Replace schematic panel. See

Ser-

vice

on page 87.

Keypad display and schematic
blink

Air supply volume too low. Increase
air volume.

Air supply pressure too high. Do not
exceed 100 psi (0.7 MPa, 7 bar).

Keypad display shows 8 2.02*

* or current software revision.
See setup level 7.

Air supply volume too low. Increase
air volume.

Continuity Checks

Follow the procedure on page 87 to access the circuit
board, keypad, or schematic panel ribbons to conduct
the continuity tests. Be sure to put on the ground strap
provided before checking continuity.

Use an ohmmeter to check continuity on the ribbon
cable for the desired light or key. Refer to the following
charts and Fig. 93 for the associated pin numbers and
locations.

NOTE:

When closed, the keys should have less than 100
ohms resistance.

Check the lights for continuity with the leads touch-
ing the pins one way then reverse polarity. If there
is no continuity reading with either check, the lights
are bad and the entire part needs to be replaced.

SCHEMATIC PANEL KEY AND LIGHT CONTINUITY CHECKS

NOTE:

The keys use the small ribbon (A). The lights use the large ribbon (B). Refer to Fig. 93.

Continuity Check

Red

Green

Feed Pump A Light

2 and 10

Feed Pump B Light

2 and 14

Full Level Reservoir A Light

2 and 5

2 and 6

Full Level Reservoir B Light

1 and 17

1 and 18

Low Level Reservoir A Light

2 and 7

2 and 8

Low Level Reservoir B Light

1 and 19

1 and 20

Low Pressure A Light

2 and 11

2 and 12

Low Pressure B Light

2 and 15

2 and 16

Premier Runaway Light

2 and 3

2 and 4

Material A Usage Light

1 and 21

1 and 22

Material B Usage Light

1 and 23

1 and 24

Continuity Check

Red

Green

High Pressure A Light

1 and 26

High Pressure B Light

1 and 28

Work Life Time Light

1 and 29

1 and 30

Solvent Runaway Light

1 and 31

1 and 32

Temperature A Light

2 and 9

2 and 13

Temperature B Light

1 and 25

1 and 27

Feed Pump A Key

1 and 3

Feed Pump B Key

1 and 4

Premier Pump Key

1 and 2

Solvent Pump Key

1 and 5

«
...
72
73
74
75
76
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Ecco Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Saturn 2000 GC/MS

Бренд: Varian Страницы: 9

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды