Graco SuperCat 232721 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 114

background image

308925

76

Care of the System

WARNING

INJECTION HAZARD

To reduce the risk of serious injury,
follow the

Pressure Relief Procedure

on page 21 whenever you are instructed
to relieve the pressure.

CAUTION

Be sure to label all fluid path parts “component A” or
“component B”. Doing so prevents interchanging A
and B parts, which will contaminate the materials and
the fluid path through the equipment.

Color-coded chemically resistant tape may be used
to label the parts. Use Part No. 070540 blue for
component A, 070541 green for component B,
070542 red for mixed material, and 070543 white for
solvent.

Clean the Reservoir Outlet Filters

Check the reservoir outlet filters (54)

weekly

. If you

have the optional low pressure sensor, a red light on
the low pressure indicator at reservoir A or B will
indicate when the filter is clogged. See Fig. 94.

To remove the filters for cleaning:

1.

Follow the

Pressure Relief Procedure

on page 21.

2.

Close the reservoir ball valves (56).

3.

Disconnect the clamps (70) and remove the com-
ponent A and B suction hoses (64).

4.

Disconnect the wire from the low pressure sen-
sors, if present.

5.

Turn the filters and remove them. Disassemble the
filters.

6.

Clean the filter element (54e) and the filter bowl
(54a) with compatible solvent.

7.

Reassemble the filters. Be sure the lips of the
u-cup (54d) face up.

8.

Reinstall the filters. Reconnect the sensor wires (if
present) and suction hoses. Open the ball valves
(56).

8337A–part

Fig. 94

1

56

70

64

54e

54a

54d

1

Lips face up.

69

«
...
74
75
76
77
78
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Rangevision Страницы: 31

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Eaton Страницы: 21

Бренд: Eaton Страницы: 70

Бренд: NANO Страницы: 4

Бренд: Ocmis Irrigazione Страницы: 100

AquaPure Ei Series

Бренд: Jandy Страницы: 4

Бренд: janitza Страницы: 30

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Oakworks Medical Страницы: 28

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды