Graco SuperCat 232721 Скачать руководство пользователя страница 63

Страница: 63 / 114

308925

Troubleshooting

Feed Pumps

Problem

Operating Condition

Cause/Solution

Feed pump does not run

In spray or manual mode, schematic
feed pump light is on

Check air regulator setting. Adjust
setting as needed.

Check feed pump setup. See below.

Check air solenoids. See page 72.

If in spray mode, check material
usage display. See page 73.

Replace circuit board. See

Service

on page 87.

In manual mode, feed pump key
pressed, schematic feed pump lights
off

Check feed pump setup. See below.

Check the electrical continuity for the
feed pump key signals and lights.
See page 74.

Replace keypad. See

Service

page 87.

Replace circuit board. See

Service

on page 87.

Full level sensor alarm

In spray mode

Check feed pump setup. See below.

Check feed pumps. See “trouble-
shooting” in the feed pump manual.

Install larger feed pumps.

Low level sensor alarm

In spray mode

Check feed pump setup. See below.

Check feed pumps. See “trouble-
shooting” in the feed pump manual.

Install larger feed pumps.

Feed pump will not stop

Schematic feed pump light off

Check feed pump air solenoid. See
page 72.

Feed Pump Setup Check

Make sure one of the level sensor options “with
feed pump” is selected. See

Setup

on page 51.

The Premier pump should go through 1 full cycle
(2 top changeovers) before the feed pumps start.

Make sure the Feed Pump Time setting is set high
enough to fill the reservoirs before an alarm oc-
curs. See

Setup

on page 49.

If both full and low level sensors are installed,
make sure the Feed Pump Time setting (

Setup

page 49) is set so the alarm for the full level sen-
sor will occur before the low level sensor alarm.
Base the settings on the Premier pump and the
feed pump capacity.

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды