Graco SuperCat 232721 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 114

background image

308925

24

Control Overview

Modes of Operation

There are three main modes of operation:

Manual Mode

Spray Mode

Setup Mode

Manual Mode

Manual Mode is used to manually operate the pumps,
which is necessary to load and prime the proportioner,
flush, and troubleshoot the system.

The system is in Manual Mode when it is powered up.
The

Manual/Spray Mode

light will be off. The system is

changed from Manual Mode to Spray Mode by press-
ing the Manual/Spray Mode

Key. See Fig. 16.

Spray Mode

Spray Mode is used during normal operation, when
material is being sprayed. When the system is in Spray
Mode, the Manual/Spray Mode light is green. See
Fig. 16.

Setup Mode

Setup Mode is used to change the values the control
uses to operate the system and to access information
about the system (such as the software revision). The
system must be in Manual Mode to access Setup
Mode. See page 25 for more information on Setup.

Operator Keypad and Display

Features

See Fig. 15.

Eight function keys

Up and down arrow keys

Eight light indicators

Six digit display

Function Keys

The eight function keys are used to operate and set up
the system. Icons above the keys represent the func-
tion of the keys. See Fig. 16.

The use of each key is further described, starting on
page 27.

A

Keypad Quick Reference

table is in the

Operation Manual 308875, included with the system.

Up and Down Arrow Keys

The up and down arrow keys are used to scroll
through values in Manual and Spray Modes and to
adjust values in Setup Mode.

Lights

Except for the Manual/Spray Mode key, the keypad
light will turn green for the key that is pressed (active
function).

If an alarm occurs, the lights for that alarm will turn red
on the schematic panel.

NOTE:

There are more alarm functions in Spray Mode

than in Manual Mode.

Display

The information on the display will correspond to the
active function key.

Fig. 15

Icon

Key

Light

Display

Up/Down
Arrows

Fig. 16

Manual/Spray Mode

Stop key

Work Life
Timer

Future

Pressure

Material Usage

Solvent
Usage

Temperature

«
...
22
23
24
25
26
...
»

Содержание SuperCat 232721



















































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperCat 232721

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренд: IKEA Страницы: 24

Бренд: Kelvin Страницы: 30

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Бренд: GGM gastro Страницы: 3

Бренд: Wartmann Страницы: 56

Бренд: GOZONE Страницы: 11

Бренд: Tatu Marchesan Страницы: 52

Бренд: Salvis Страницы: 28

Бренд: AGI Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды