Graco SuperCat 232721 Скачать руководство пользователя страница 88

Страница: 88 / 114

308925

Service

Replacing the Circuit Board

11. Unscrew the six hex standoffs (125d), and remove

the circuit board (125c). See Fig. 106.

12. Secure the new circuit board (125c) to the panel

with the hex standoffs (125d).

Replacing the Wire Harness

13. Disconnect the wire harness. Note labeling or

orientations for reconnection. Create tags or notes
as required for proper installation of the new wiring
harness.

14. Remove the circuit board cover (125b).

15. Disconnect the cable from the circuit board (125c).

Create tags or notes as required for proper instal-
lation of the new cable.

16. Cut the wire ties holding the cable to the propor-

tioner. Remove the cable from the wiring conduit.

Reassembly

17. Connect the ribbon cable to the circuit board

(125c). See Fig. 106.

18. Place the cover (125b) over the circuit board

(125c), and secure it with the screws (125f).

19. Connect the wire harnesses to the two circuit

board connectors.

20. Close the access door (125); be sure not to crimp

or pinch the wires. Secure the door with the
screws (135).

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды