Graco SuperCat 232721 Скачать руководство пользователя страница 52

Страница: 52 / 114

308925

Setup Functions

Target Ratio Key 5, Level 1–4, 6

Keys are currently inactive.

Target Ratio Key 5, Level 5

Units of Measurement

Default Setting:

U.S. Measurement (psi/gallons/

Purpose

To set the proportioner to count and display accord-
ing to the user’s standard unit of measurement.

Access

In setup level 5, press key 5 on the keypad to access
the Units of Measurement function.

Keypad Display

The key 5 light is green and 1 appears in the keypad
setup level position. See Fig. 76.

System Schematic Panel

There is no system schematic display related to the
units of measurement function.

Changing Values

Press an arrow key until the number for the desired
unit of measurement displays.

U.S. Measurement (psi/gallons/

Metric – Asian (MPa/liters/

Metric – European (bar/liters/

Fig. 76

Pressure Key 5, Level 7

Byte Code Information

Purpose

To display the byte code information for the currently
installed software.

Fig. 77

Содержание SuperCat 232721



















































































































Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды

Graco SuperCat 232721, Инструкция-перечень запасных частей

Результаты поиска

Содержание SuperCat 232721

Отзывы:

Похожие инструкции для SuperCat 232721

Бренды по названию

Популярные бренды