GE Voluson Swift Скачать руководство пользователя страница 224

Страница: 224 / 344

10.3.1.1 GS (Gestational Sac)

There are two methods to measure the GS:
1.

Three distance measurement (mean value = GS diameter)

One distance measurement (value = GS diameter)

Method 1

The three distance measurement requires three measurements (length, width, height) before

the age is displayed. The age is derived from the mean value of all three measurements.
The workflow is identical to the measurement "3 Dist".

Method 2

One distance measurement is required before the age is displayed. The age is derived from

the distance measurement.
To use this method:
1.

Select GS. A cursor appears.

Measure the GS distance like a normal distance measurement. The result is displayed

immediately.

10.3.1.2 Sono NT (Nuchal Translucency)

Note

This measurement can be adjusted and customized in the system setup.

To measure the contour detection of the NT border:
1.

Select

. The measurement cursor appears.

Select the fetal position ("Face Up" or "Face Down").

Position and fix the first point P1 of the rectangular ROI.

Position and enter the second point P2 of the rectangular ROI. The NT border detection

is performed. If a valid result is found, the borders are shown in red and the NT distance

is displayed with two crosses.

Only if the found measurement is correct according to the guidelines, accept and confirm

the result. Then it will be stored in the report. If the system cannot detect a result, a

warning message appears.

Note

If the current US image magnification is too low (the corresponding pixel size is bigger than

0.1mm), a magnification hint is displayed if activated in the system setup. When this hint

appears, increase the magnification and redo the measurement.

Note

It is possible to select the calculation method by pressing Method: (i-i: inner-inner or i-m: inner-

middle).

Figure 10-3 Display of the Sono NT analysis (sample)

Measurements and Calculations

10-16

Voluson™ SWIFT / Voluson SWIFT+ Instructions For Use

5831612-100 Revision 4

Содержание Voluson Swift

























































































































































































































































































































































Результаты поиска

Содержание Voluson Swift

Отзывы:

Похожие инструкции для Voluson Swift

Бренды по названию

Популярные бренды

GE Voluson Swift, Инструкция по эксплуатации

Результаты поиска

Содержание Voluson Swift

Отзывы:

Похожие инструкции для Voluson Swift

Бренды по названию

Популярные бренды