Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 9 / 103

6.4L POWER STROKE

DIESEL OvERvIEW

Engine Serial Number

• The engine serial number is located on the left rear corner

of the crank case on a half moon machined surface.

• A white sticker is placed over this number during production,

this sticker was removed for illustration purposes.

• 6.4 - is the engine family identifier.

• HU2Y - is a manufacturing designator

Ex: HU2Y or HU2U “Y designates Huntsville, AL

and U designates Indianapolis, IN”

• 0385535 - is a sequential build number

Serial Number Label

• Located on the top of the vertical EGR cooler.

• States the engine serial number.

- example at right, “0385535”

• States the engine family.

- example at right, “6.4L DI turbo diesel”

Emissions Label

• States the horsepower rating for the engine,

programmed in the Engine Control Module (ECM).

• Depicts where the engine meets or

exceeds emission standards.

• Shows the engine displacement.

• Is affixed to the right hand valve cover.

• F250/350 labels are red.

• F450/550 labels are blue.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды