Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 32 / 103

Fuel Return Banjo Bolt

Filter Housing

Engine Mounted
Fuel Filter

Filter Cap

Fuel Supply

Fuel Pressure
Regulator Located
Inside Standpipe
Assembly

Fuel Return to Tank

Fuel Return
from Cooler

Filtered Fuel
Outlet

Fuel Temperature
Sensor (FTS)

fuel supply system

Engine Mounted Fuel Filter

• An engine mounted fuel filter is mounted

to the intake manifold.

• The engine mounted fuel filter is a 4

micron cartridge style filter.

• It also incorporates a fuel pressure regulator

(in the standpipe) and an air bleed. Fuel from

the regulator is returned to the HFCM.

NOTE: Please exercise extreme cleanliness

when servicing the fuel filter.

Fuel Pressure Regulator

• The fuel pressure regulator is located inside the

engine mounted fuel filter housing in the standpipe.

• It regulates fuel pressure by routing unfiltered

fuel from the filter housing to the HFCM via

a spring loaded poppet style valve.

• The cracking pressure (pressure at which the valve

begins to open) of the valve is 2psi +\- 0.5psi. Actual

fuel pressure may be above or below this specification.

• The regulated pressure of the valve is

3psi+/- 0.5psi. Actual fuel pressure may

be above or below this specification.

NOTE: The fuel pressure regulator is NOT serviceable

separate from the housing! If the regulator needs to be

replaced, then the entire housing must be replaced.

Fuel Return Banjo Fittings

•

The fuel return lines (located on the front of

each cylinder head) utilize a banjo bolt to route

the return fuel back to the fuel system.

NOTE: The 6.0L Power Stroke

Diesel utilized a banjo

bolt with a check valve inside. Do not interchange the 6.0L

banjo bolt with the 6.4L banjo bolt.
NOTE: The 6.4L Power Stroke Diesel uses an open banjo

bolt with no check valve. The check valves are no longer

needed since the drilled passages in the cylinder heads are

now utilized as fuel return passages.

Fuel supply system

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды