Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 91 / 103

diagnostic codes

DTC

How Set

Code Description

Brief Description

Software Parameters

Required to Set Code

Service Instructions /

Part Replaced

O R C

P1111

System Pass

PCM, connection to service tool

P000E

Fuel Volume Regulator Control

Adaptive Learning at Limit

This error is set when the Pulse Width Modulated (PWM)

signal for the Volume Control Valve (VCV) is either

too low or too high for current operating modes.

+/- 8% error in VCV control

Low pressure fuel system,

injector leakage

P0A09

DC/DC Converter

Fault Circuit Low

The purpose is to diagnose the analog output

voltage from the DCDC converter (voltage converter

for injectors inside PCM). If the voltage from the

converter is lower than a threshold, the fault is set.

Low: < 42 V
High: >96 V

PCM

P0A10

DC/DC Converter

Fault Circuit High

The purpose is to diagnose the analog output voltage

from the DCDC converter (voltage converter for

injectors inside PCM). If the voltage from the converter

is higher than a threshold, the fault is set.

Low: < 42 V
High: >96 V

PCM

P0001

Fuel Volume Regulator

Control Circuit / Open

This error is recorded when an open circuit causes the Pulse

Width Modulated (PWM) signal of the Volume Control Valve

(VCV) to be abnormally high for an extended period of time.

For open load: Resistance > 500 Ohm

Wiring, VCV electrical system

P0003

Fuel Volume Regulator

Control Circuit Low

During KOEO diagnostics, this error is set when the

measured current through the system is greater than

intended. During the KOER or Continuous Monitor modes,

this code is a result of a short to ground, which causes the

measured current in the system to be lower than expected.

Short to ground: 0 V
> 3A

Wiring, VCV electrical system

P0004

Fuel Volume Regulator

Control Circuit High

This error is set if there is short to ground, short to power,

or an open load detected in the volume control circuit.

Short to plus: 12 V”

Wiring, VCV electrical system

P0069

MAP - Barometric

Pressure Correlation

This error is set when the difference between

Manifold Absolute Pressure (MAP) and Barometric

Pressure (BP) is greater than the specified

value for a predetermined period of time.

300 hPa < 2.5 sec

Wiring, MAP sensor, BP sensor

(intergral part of PCM)

P006B

KO MAP/EBP Correlation

This error is set when the difference between Maniforld

Absolute Pressure (MAP) and Exhaust Pressure (EP) is greater

than the threshold for a predetermined period of time.

Engine off time > 5.0s.
300 hPa > 5.0 sec

Wiring, EP tube plugged, EP

Sensor, MAP sensor, PCM

P008C

Fuel Cooler Pump

Control Circuit / Open

This diagnostic will detect if the relay for the

fuel cooling pump has an open load error.

P008D

Fuel Cooler Pump

Control Circuit Low

This diagnostic will detect if the relay for the

fuel cooling pump has grounded.

P008E

Fuel Cooler Pump

Control Circuit High

This diagnostic will detect if the relay for the fuel

cooling pump has shorted to positive voltage.

P008F

Engine Coolant Temperature /

Fuel Temperature Correlation

This error is set when the difference between Engine

Coolant Temperature (ECT) and Fuel Temperature

(FTS) is either greater than or less than a specified

value depending on current operating modes.

Engine off time > 3600 sec
no block heater detected
20 deg C or -20deg < 1 sec

Wiring, ECT or TFU sensor,

unknown type block

heating device, PCM

P0087

Fuel Rail/System

Pressure - Too Low

This error will be set if the fuel pressure in the rail is too

low and the controller cannot regulate it to the setpoint.

20 % “overposition” of the

PCV or VCV [% PWM]
5% deviation of the fuel rail pressure

to the fuel rail pressure setpoint.

Low pressure system, wiring to

VCV and PCV, FUP sensor, pump

P0088

Fuel Rail/System

Pressure - Too High

This error will be set if the fuel pressure in the rail is too

high and the controller cannot regulate it to the setpoint.

20 % “overposition” of

the PCV [% PWM]
3% deviation of the fuel rail pressure

to the fuel rail pressure setpoint

Low pressure system, wiring to

VCV and PCV, FUP sensor, pump

P0090

Fuel Pressure Regulator

Control Circuit

This error occurs if a short to power is found in

the fuel pressure regulator (PCV) circuit.

For open load: Resistance > 500 Ohm

Wiring to PCV, PCV

electrical system

P0091

Fuel Pressure Regulator

Control Circuit Low

This error occurs if a short to ground or, during the

KOEO self test, a current that is excessively high is

found in the fuel pressure regulator (PCV) circuit.

Short to ground: 0 V
> 3A

Wiring to PCV, PCV

electrical system

P0092

Fuel Pressure Regulator

Control Circuit High

This error occurs if an open circuit is found in

the fuel pressure regulator (PCV) circuit.

Short to plus: 12 V

Wiring to PCV, PCV

electrical system

- Self Test - Key On Engine Off

- Key On Engine Running

- Continuous Operation

REGEN

- Test Follows a REGEN CYCLE

SHUT DOWN

- Test Follows Key Off

- Test Operates at Key On

1PC

- Once Per Cycle

DATA Color Code

MIL For Both F250/F350 and F450/F550

MIL For Only F250/F350

MIL For F250/F350 and Wrench for F450/F550

Wrench for Both F250/F350 and F450/F550

No MIL or Wrench Light

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды