82
special torque chart (reference only)
Note: All torque specs are ±10% unless stated otherwise.
COMPONENT
STANDARD
METRIC
Bedplate mounting bolts (crankcase bolts)
Figure C
Figure C
Camshaft follower guide bolt/washer
114 lbf/in
13 Nm
Camshaft position (CMP) sensor
114 lbf/in
13 Nm
Camshaft thrust plate mounting bolts
23 lbf/ft
31 Nm
Connecting rod bolt (Initial)
33 lbf/ft
45 Nm
Connecting rod bolt (Final)
50 lbf/ft
68 Nm
Coolant (block) heater
30 lbf/ft
41 Nm
Coolant pump mounting bolts
23 lbf/ft
31 Nm
Coolant pump pulley mounting bolts
23 lbf/ft
31 Nm
Crankcase breather to valve cover
114 lbf/in
13 Nm
Crankcase breather drain fitting to crankcase
18 lbf/ft
25 Nm
Crankcase breather tube clip bolt
23 lbf/ft
31 Nm
Crankcase coolant drain plug (M16)
180 lbf/in
20 Nm
Crankshaft position (CKP) sensor
114 lbf/in
13 Nm
Cylinder head bolts (only use new bolts, note 3)
Figure A
Figure A
EGR cooler inlet temperature sensor (EGRT Inlet)
32 lbf/ft
44 Nm
EGR coolant system hose clamps
31 lbf/in
3.5 Nm
EGR cooler outlet temperature sensor (EGRT Outlet)
28 lbf/ft
38 Nm
EGR DOC tube to RB up-tube bolts & nuts
23 lbf/ft
31 Nm
EGR DOC tube to EGR cooler horizontal bolts
23 lbf/ft
31 Nm
EGR cooler band clamps
Figure K
Figure K
EGR cooler vertical to EGR valve housing bolts
23 lbf/ft
31 Nm
EGR cooler vertical bracket mounting bolts
23 lbf/ft
31 Nm
EGR cooler horizontal to EGR cooler vertical flange
23 lbf/ft
31 Nm
EGR throttle body to EGR valve housing
88 lbf/in
10 Nm
EGR valve housing to intake manifold
88 lbf/in
10 Nm
EGR valve to EGR valve housing
88 lbf/in
10 Nm
Engine coolant temperature sensor (ECT)
159 lbf/in
18 Nm
Engine oil pressure switch (EOP)
124 lbf/in
14 Nm
Engine oil temperature sensor (EOT)
159 lbf/in
18 Nm
Exhaust backpressure (EP) connector to DOC tube
20 lbf/ft
27 Nm
Exhaust backpressure (EP) tube bracket nut
80 lbf/in
9 Nm
Exhaust backpressure (EP) tube nut to EP sensor
180 lbf/in
20 Nm
Exhaust backpressure (EP) tube nut to exhaust connector
180 lbf/in
20 Nm
Exhaust manifold flange studs
159 lbf/in
18 Nm
Exhaust manifold heat shield mounting bolts & nut
88 lbf/in
10 Nm
Exhaust manifold heat shield spacers to stud bolts
88 lbf/in
10 Nm
Exhaust manifold mounting bolts and stud bolts (note 4)
Figure F
Figure F
Exhaust up-tube to exhaust manifold nuts
23 lbf/ft
31 Nm
Exhaust up-tube to turbo bolts
18 lbf/ft
24 Nm
Flywheel/flexplate bolts (only use new bolts, note 3)
Figure B
Figure B
Front cover mounting bolts
23 lbf/ft
31 Nm
Fuel cooler reservoir mounting bolts
114 lbf/in
13 Nm
Fuel filter cap
20 lbf/ft
27 Nm
Fuel fitting banjo bolt with copper washer (M12)
28 lbf/ft
38 Nm
Fuel fitting banjo bolt with steel washer w/viton insert (M12)
18 lbf/ft
25 Nm
Fuel fitting banjo bolt (M14)
35 lbf/ft
47 Nm
Fuel injector hold down clamp bolts
28 lbf/ft
38 Nm
Fuel injector return tube nut to check valve
28 lbf/ft
38 Nm
Fuel return passage plug (rear of cylinder head)
20 lbf/ft
27 Nm
Fuel rail pressure sensor (FRP)
Figure L
Figure L
Fuel supply and return tube clamp to upper oil pan
23 lbf/ft
31 Nm
Содержание 6.4L Power Stroke
