Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 81 / 103

152

UniqUe service ProcedUres

153

Exhaust Up-Pipe Service

• Assembly of the exhaust up-pipes and EGR cooler

supply pipe must be performed in the proper order.

• The pipes must first be installed loosely in the

order shown, then torqued in the proper sequence

as shows in the Ford workshop manual.

NOTE: Failure to follow the assembly

steps can result in exhaust leaks.

EGR Cooler Service

• Servicing the EGR coolers must be

performed in the proper order.

• The coolers must first be installed loosely in the

order shown, then torqued in the proper sequence

as shown in the Ford workshop manual.

• Proper assembly is crucial due to the extreme

temperature changes within the EGR coolers.

Temperature changes of 800 deg F are possible.

NOTE: All bolts, nuts, clamps, and cooler brackets

must be replaced if the coolers are removed

1st 2nd

3rd

1st

2nd

Intake Manifold And Gaskets

• When reinstalling the intake manifold, the locating

tabs on the intake manifold gasket should face

up and toward the center of the engine.

154

Locating Tabs

Closeup Showing
Locating Tab Fitment
Into Intake Manifold

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды