Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 69 / 103

Actuators & Control Modules

• Pressure Control Valve (PCV)

• Volume Control Valve (VCV)

• Exhaust Gas Recirculation Valve (EGR)

• Turbocharger Actuator

• Glow Plug Control Module (GPCM)

• Glow Plugs

• Piezo Electric Fuel Injectors

• Throttle Body

120

ElEctrical componEnts

121

122

Control Devices

• The 6.4L Power Stroke

Diesel uses eight (8) control

devices: Pressure Control Valve, Volume Control Valve,

EGR Valve, Turbocharger Actuator, Glow Plug Control

Module, Glow Plugs, Fuel Injectors, and the Throttle Body.

PCV (Pressure Control Valve)

• The PCV governs the fuel pressure that is

delivered to the fuel injectors via the high

pressure fuel rails and fuel supply tubes.

• The PCV also acts as a dampening device for the

fluctuations in pressure that occur during fuel delivery

through the pump and the injection process.

• The PCV is controlled by the ECM to maintain optimal fuel

pressure throughout all engine operating conditions.

• The PCV is permanently mounted to the high

pressure pump and is not to be removed.

Removal of the PCV will result in replacement

of the high pressure fuel injection pump.

NOTE: Fuel caps have been left off for visualization

purposes. Always use fuel caps when

servicing the high pressure fuel system!

VCV (Volume Control Valve)

• The VCV regulates the delivery of fuel from the internal

transfer pump (ITP) to the high pressure pumping elements.

• The VCV adjusts the low pressure side of the system to

match the needs of the engine thus increasing efficiency.

• The VCV is permanently mounted to the high

pressure pump and is not to be removed.

Removal of the VCV will result in replacement

of the high pressure fuel injection pump.

NOTE: Fuel caps have been left off for visualization

purposes. Always use fuel caps when

servicing the high pressure fuel system!

Pressure Control
Valve (PCV)

Volume Control
Valve (VCV)

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды