Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 71 / 103

126

ElEctrical componEnts

127

128

ECM (Engine Control Module)

• The ECM, which is mounted behind the engine on the

passenger side cowl, uses sensor inputs to control

actuators and send fueling commands to the fuel inectors.

• The ECM controls the fuel and air management

system on the 6.4L Power Stroke

Diesel.

Glow Plug System

• The glow plug system is used to warm the

air in the cylinders to enhance cold weather

startability and reduce start up smoke.

• The glow plug system is ECM controlled,

and powered by the GPCM.

Glow Plug Control Module(GPCM)

& Glow Plug Harness

• The GPCM is a unit that controls the glow plugs

in order to warm the air in the cylinders.

• The GPCM uses a glow plug enable signal to turn the

glow plugs on for a time controlled by the ECM.

• The GPCM is capable of diagnosing a problem with one

glow plug and then sending a diagnostic signal to the ECM.

• It also has the ability to turn off one glow plug

if a short is detected in that circuit.

• Each bank of glow plugs is connected to

the engine wiring harness via a glow plug

harness, either left bank or right bank.

• The glow plug harness has four connectors that

supply power to the glow plugs and seal oil from

escaping through the glow plug access holes.

Glow Plug Harness

Chassis Connector

Engine Connector

GPCM

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды