Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 97 / 103

diagnostic codes

DTC

How Set

Code Description

Brief Description

Software Parameters

Required to Set Code

Service Instructions /

Part Replaced

O R C

P0528

Fan Speed Sensor

Circuit No Signal

P0529

Fan Speed Sensor

Circuit Intermittent

P0544

Exhaust Gas Temperature

Sensor Circuit Bank 1 Sensor 1

This error occurs if the EGT1 temperature signal of the

exhaust system does not rise sufficiently immediately

after a cold-start following an 8-hour soak.

P0545

Exhaust Gas Temperature

Sensor Circuit Low

- Bank 1 Sensor 1

This error occurs when the EGT1 sensor temperature

signal is higher (lower voltage signal) than a maximum

probable temperature, indicating a short to ground.

P0546

Exhaust Gas Temperature

Sensor Circuit High

- Bank 1 Sensor 1

This error occurs when the EGT1 sensor temperature signal

is lower (higher voltage signal) than a minimum probable

temperature, indicating an open circuit or a short to power.

P0560

System Voltage

This error occurs when battery voltage falls

below a predetermined threshold.

P0563

System Voltage High

This error occurs if the battery voltage increases

above a predetermined threshold.

P0565

Cruise Control ON Signal

This error occurs is the cruise control on switch is

not pressed during the KOER or the cruise control on

switch is stuck on during continuos operation.

P0566

Cruise Control OFF Signal

This error occurs when the cruise control off switch

is not depressed during the KOER self test or when

the switch is stuck during continuous operation.

P0567

Cruise Control RESUME Signal

This error occurs when the cruise control resume

switch is not depressed during the KOER self test

or is stuck during continuous operation.

P0568

Cruise Control SET Signal

This error occurs when the cruise control set

switch is not depressed during the KOER self test

or is stuck during continuous operation.

P0569

Cruise Control COAST Signal

This error occurs when the cruise control coast

switch is not depressed during the KOER self test

or is stuck during continuous operation.

P0571

Brake Switch A Circuit

This error occurs when the brake switch is not

depressed during the KOER self test.

P0578

Cruise Control Multi-Function

Input A Circuit Stuck

This error occurs if the voltage received by the PCM for the

cruise control circuit is above the calibrated threshold.

P0579

Cruise Control Multi-

Function Input A Circuit

Range/Performance

This error occurs when all cruise control

circuit voltages are equal to zero.

P060B

Internal Control Module A/D

Processing Performance

This error occurs is the voltages for main

controller and monitoring controller within the

PCM are outside of a predetermined range.

ECU

P060C

Internal Control Module

Monitoring Processor

Performance

This error occurs if a fault occurs to the

monitoring processor within the PCM.

Verify reprogramming files,

reflash module, change ECU

P060D

Internal Control Module

Accelerator Pedal

Position Performance

Pedal, wiring to pedal, PCM

P0600

Serial Communication Link

PCM

P0602

Powertrain Control

Module Program Error

VID Block program, PCM

P0603

Powertrain Control Module

Keep Alive Memory (KAM) Error

This error occurs if a fault is detected in

the keep alive memory circuit.

engine not longer running

than 600 sec

PCM

- Self Test - Key On Engine Off

- Key On Engine Running

- Continuous Operation

REGEN

- Test Follows a REGEN CYCLE

SHUT DOWN

- Test Follows Key Off

- Test Operates at Key On

1PC

- Once Per Cycle

DATA Color Code

MIL For Both F250/F350 and F450/F550

MIL For Only F250/F350

MIL For F250/F350 and Wrench for F450/F550

Wrench for Both F250/F350 and F450/F550

No MIL or Wrench Light

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды