Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 19 / 103

Cooling system

Cooling System Flow: Oil Cooler

• Coolant is directed out of the crankcase and into the oil filter base at

the front of the engine.

• The oil filter base routes the coolant down into the front of the oil

cooler then toward the rear of the engine.

• Once the coolant has passed through the oil cooler it is routed

up to the top of the oil cooler then directed towards the front

through a port where it is then routed down, out of the cooler,

through a port in the block.

Coolant
Inlet from
Crankcase

Inlet to
Cooler

Coolant
Outlet to
Crankcase

Outlet
from Cooler

Oil Cooler Cover
(Top View)

Oil Cooler Cover
(Bottom View)

Oil Cooler Cover

Oil Filter Base

Oil Cooler

Oil Cooler Coolant Flow

Cooling System Flow: Back of Front Cover

• Coolant is sealed via a metal one piece gasket and is

directed out of the front cover through three (3) passages.

• Two of the passages route coolant to the crankcase to cool

the cylinder walls and cylinder heads (there are different

sized orifices pressed into the crankcase in these two

passages).

• The third passage routes coolant to the oil cooler via a

passage in the crankcase.

• There are two passages for coolant to return from the

crankcase into the front cover.

COOLANT IN
(from block)

COOLANT OUT
(to block)

Coolant
Orifices

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды