Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 66 / 103

ElEctrical componEnts

117

EP (Exhaust Pressure)

• The EP sensor is a three (3) wire variable capacitance sensor.

• The ECM supples a 5 volt reference signal which the EP sensor

uses to produce a linear analog voltage that indicates pressure.

• The EP measures exhuast back pressure so that the ECM can control the

EGR, and the high pressure turbocharger via the turbocharger actuator.

NOTE: Washing a hot engine can have negative effects on this sensor!

NOTE: This sensor is gray in color for the 6.4L and black in color for the

6.0L. Some early 6.4L engines may be equipped with black sensors.

Do not interchange 6.0L EP sensors with 6.4L EP sensors, these sensors

are different.

NOTE: Pay special attention to differentiating between the MAP

sensor and the EP sensor, do not interchange them!

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды