Ford 6.4L Power Stroke Скачать руководство пользователя страница 75

Страница: 75 / 103

134

UniqUe service ProcedUres

135

136

Fuel System Service: High Pressure Fuel Tubes

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• High pressure fuel supply tubes must always be replaced

once loosened. Never re-use a high pressure tube once

it has been loosened under any circumstances!

NOTE: Always use the fuel injector connector

disconnect tool (tool # 310-157) whenever

disconnecting the fuel injector electrical connector.

Failure to use this tool can damage the connector.

Fuel System Service: High

Pressure Fuel Tube Service

NOTE: Use proper cleanliness practices

while servicing the fuel system!

NOTE: Follow the proper service procedures while servicing

the fuel system and always use the correct torque!

• Proper torque is crucial with the 6.4L Power

Stroke

Diesel’s high pressure fuel system.

• When replacing high pressure fuel tubes, always follow

the correct procedure for installation and torque.

Fuel System Service Cleanliness: High

Pressure Fuel Injection Pump

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• Always use fuel system caps when servicing

the high pressure fuel injection pump.

• Do not have the fuel system open to the elements any

longer than is necessary to perform the job at hand.

• Tool # 310-158 (fuel caps)

Fuel Rail Caps

High Pressure Fuel
Injection Pump Caps

High Pressure Fuel Tubes

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды