Ford 6.4L Power Stroke Скачать руководство пользователя страница 21

Страница: 21 / 103

Cooling system

Glow Plug Sleeve

• Glow plug sleeves are used to keep coolant from coming in

direct contact with the glow plugs and to seal coolant from

the combustion chamber.

• The glow plug sleeve is replaceable. See unique service

procedures or the service manual for more details.

Degas Bottle

• The degas bottle is located on the left side of the engine

compartment and is part of the left side battery tray.

• One of the ports on the bottle is attached to the EGR valve

coolant line (which is supplied from the top of the vertical

EGR cooler). If this port or hose is blocked, damage could

occur to the EGR coolers and/or the EGR valve.

Glow Plug Sleeve

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды