Ford 6.4L Power Stroke Скачать руководство пользователя страница 23

Страница: 23 / 103

Lubrication SyStem

Lubrication System Oil Flow

• Oil is drawn from the oil pan through the pick-up tube. The

oil is then routed through a passage cast into the upper oil

pan before being routed through a passage in the block, a

passage in the front cover, and finally to the oil pump inlet.

• The regulator valve utilizes a force, provided via the regulator

spring, to apply a pressure equal to 65 psi. Whenever oil pressure

exceeds this force, the regulator valve will move downward

and allow the excess pressure to bleed off back through a

passage that routes the oil back to the inlet side of the pump.

• From the oil pump, oil is directed to the oil

cooler and then to the oil filter.

• From the oil filter the oil is supplied to a chamber incorporating

five (5) passages. One (1) is to the turbochargers for

lubrication. Two (2) are to the EOT and EOP sensors.

• The two (2) other passages are to the tappet oil

supply on the right and left banks. The tappet galleries

also provide oil to the piston cooling jets.

• Cross drillings off of the right bank tappet

gallery supply oil to the main bearings.

• Another cross drilling vertically up from each main

bearing supplies oil to the camshaft bearings.

Note: This oil supply routing is different than the 6.0L

and uses different bearings which are also placed

differently with respect to the oil holes.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды