Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 78 / 103

143

UniqUe service ProcedUres

144

145

EGR Valve Removal

• Removing the EGR valve must be performed using the

proper EGR valve removal tool.

• This tool is comprised of numerous pieces that

must be put together around the EGR valve.

• Once the removal tool is assembled on the valve,

the valve can be slowly pulled from its housing.

• Tool # 303-1267

NOTE: Pay close attention that the removal tool is

installed and used correctly while removing the valve

or damage can occur to the EGR valve and/or tool.

Crossover Tube Seal Removal

• Crossover tube seal removal requires the use of special

service tools; slide hammer, seal removal tools.

• There is a different size removal tool for

each opening of the crossover tube.

• Tool # 303-1264

Crossover Tube Seal Installation

• When installing new seals into the turbocharger crossover

tube, always use the appropriate installation tools.

• The seals for each passage are two (2) different

sizes. Make sure you use the correct sized

seal installation tool for each sized seal.

NOTE: Make sure you have the crossover tube mounted

securely to assure proper seal installation.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды