Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 27 / 103

Oil Filter Element

Lubrication SyStem

Oil Pump Flow (back side)

• The oil pump is a gerotor style pump driven off of

the flats on the front of the engine’s crankshaft.

• The 6.4L oil pump is held in its own removeable aluminum

housing which also contains the regulator valve.

• Oil is drawn into the pump via the combination of

atmospheric pressure (applied to the oil in the pan)

and the low pressure area that is created between the

gerotor gears on the inlet side of the pump whenever

the pump is being driven by the crankshaft.

• Once this happens, the oil will flow into the pump and

the pump will create a generous amount of oil flow.

• When the oil reaches various restriction

throughout the engine, pressure is created.

• Pressure is limited via a pressure regulator valve located

inside the pump housing. Whenever a pressure of 65

psi is reached, the regulator valve will open and allow

pressurized oil to flow back through a relief passage to the

inlet side of the pump, thus regulating system pressure.

Oil Filter

• The 6.4L Power Stroke

Diesel uses a cartridge

style oil filter, located on the top of the engine.

• When the oil filter is removed, the oil filter

housing drain valve is automatically opened to

drain most of the oil from the housing.

• The oil filter element snaps into the oil filter lid.

Note: The oil filter lid should be removed before

draining the oil from the oil pan so that the oil can

drain from the filter housing into the oil pan.

Turbocharger Oil Supply

• Oil is supplied to the turbochargers from the oil filter

base via a steel oil line, a steel T fitting, and two

separate steel lines to each turbo (the high pressure

turbocharger oil supply line has a flexible link in it).

• The oil lines are connected to each turbo via

banjo fittings and washer gaskets.

Note: The washer gaskets (which are used as a gasket

medium) must be replaced each time the banjo fittings are

loosened.

Inlet From Oil Pan

Back Side of Pump

Outlet to
Oil Cooler

Regulator
Valve

Relief Passage

Low Pressure Turbocharger
Oil Supply

High Pressure Turbocharger
Oil Supply

Pump Rotation

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды