Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 95 / 103

diagnostic codes

DTC

How Set

Code Description

Brief Description

Software Parameters

Required to Set Code

Service Instructions /

Part Replaced

O R C

P0301

Cylinder 1 Misfire Detected

This error occurs if the case of a loss of combustion.

P0302

Cylinder 2 Misfire Detected

This error occurs if the case of a loss of combustion.

P0303

Cylinder 3 Misfire Detected

This error occurs if the case of a loss of combustion.

P0304

Cylinder 4 Misfire Detected

This error occurs if the case of a loss of combustion.

P0305

Cylinder 5 Misfire Detected

This error occurs if the case of a loss of combustion.

P0306

Cylinder 6 Misfire Detected

This error occurs if the case of a loss of combustion.

P0307

Cylinder 7 Misfire Detected

This error occurs if the case of a loss of combustion.

P0308

Cylinder 8 Misfire Detected

This error occurs if the case of a loss of combustion.

P0336

Crankshaft Position Sensor A

Circuit Range/Performance

This error occurs if the tooth count of the crankshaft trigger

wheel reaches a threshold and the system is still not

detecting sync between CKP and CMP circuits while a valid

CMP sensor signal has been detected (intermittent CKP

signal), when the number of missing or extra teeth exceed

the threashold, or if spikes are detected in the CKP signal.

3 CAM edges <1sec

Wiring, CMP sensor,

CKP sensor, PCM

P0337

Crankshaft Position Sensor

A Circuit Low Input

This error occurs when a short or open fault in

the CKP circuit is present causing the amplitude

of the AC voltage to be excessive.

0.5v < 1sec

Wiring, CKP sensor, PCM

P0341

Camshaft Position Sensor A

Circuit Range/Performance

This error occurs when either the number of CMP

signals is too great to filter or the CMP signal is

not properly aligned with the CKP signal.

Internal to the engine control module
Once at key on < 1 sec

Wiring, CMP sensor, PCM

P0342

Camshaft Position Sensor

A Circuit Low Input

This error occurs when the CMP signal is missing entirely.

Internal to the engine control module
Once at key on < 1 sec

Wiring, CMP sensor, PCM

P0381

Glow Plug/Heater

Indicator Circuit

The instrument cluster performs the diagnostic of the

wait-to-start indicator once per driving cycle and transmits

the result to the PCM. The PCM analyzes the message

to check if the glow plug lamp circuit is operational.

P040B

Exhaust Gas Recirculation

Temperature Sensor A Circuit

Range/Performance

This error occurs when the change in the EGR

cooler inlet temperature is less than 40 deg

C for a predetermined period of time.

Initial ECT < 30 deg C.
ECT increase to > 80 deg

C during drive cycle
ECM on time > 3 seconds
TEGR_IN has not changed more

than 6 deg. C in 2 drive cycles

Wiring, Tegr_IN sensor, PCM

P040C

Exhaust Gas Recirculation

Temperature Sensor

A Circuit Low

This error occurs when the EGR cooler inlet

sensor temperature output value is higher

(lower voltage signal) than a maximum probable

temperature, indicating a short to ground.

0.07v > 5sec.

Wiring, Tegr_IN sensor, PCM

P040D

Exhaust Gas Recirculation

Temperature Sensor

A Circuit High

This error occurs when the EGR cooler inlet sensor

temperature output value is lower (higher voltage

signal) than a minimum probable temperature,

indicating an open circuit or short to power.

N > 650 rpm
torque setpoint >53 N-m
ECT > 60 deg C
4.65v >5sec

Wiring, Tegr_IN sensor, PCM

P0401

Exhaust Gas Recirculation

Flow Insufficient Detected

This error is set when the estimated EGR percent is less

than the minimum limit for the operating condition.

DPF regeneration not requested
PTO not active
Pressure ratio across EGR valve < 1
rate of change of engine speed < 0.05
rate of change of indicated

torque setpoint < 0.05
600 rpm <engine speed< 800 rpm
45Nm <tqi_sp< 174Nm
12 sec to run test
2 low flow failures required to set

fault (test runs 5 times per trip)
60 sec wait time between tests

EGR system error

- Self Test - Key On Engine Off

- Key On Engine Running

- Continuous Operation

REGEN

- Test Follows a REGEN CYCLE

SHUT DOWN

- Test Follows Key Off

- Test Operates at Key On

1PC

- Once Per Cycle

DATA Color Code

MIL For Both F250/F350 and F450/F550

MIL For Only F250/F350

MIL For F250/F350 and Wrench for F450/F550

Wrench for Both F250/F350 and F450/F550

No MIL or Wrench Light

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды