Ford 6.4L Power Stroke Скачать руководство пользователя страница 43

Страница: 43 / 103

Fuel ManageMent SySteM

High Pressure Fuel System Flow

• Fuel is supplied to the high pressure fuel injection pump

after being filtered by both the HFCM (horizontal fuel

conditioning module) and the engine mounted fuel filter.

• The high pressure fuel injection pump is gear driven

off of the camshaft gear at the rear of the engine.

• Once the high pressure fuel injection pump

pressurizes the fuel it is routed to two (2) high

pressure fuel rail supply tubes, one for each bank.

HIgH PReSSuRe Fuel SySteM

• The high pressure fuel rail supply tubes route the fuel to

the high pressure fuel rail located under the valve cover.

• The high pressure fuel rail inlet protrudes

through the valve cover spacer at the back of the

engine and oil is sealed by a rubber seal.

• The high pressure fuel rail routes fuel to each of the

four (4) fuel injectors through four (4) separate fuel

injector supply tubes all located under the valve cover.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды