(1) Charging the battery (Approx. 3.5 hours to full charge)
a. Connect the adaptor DC plug in Power Connector on the side of the controller.
b. In order to activate charge of battery, the volume knob must be kept “OFF”condition.
c. Connect the AC power adaptor to outlet (wall socket).
d. When the lamp changes red to green, the charge is completed.
e. Disconnect AC Adaptor from Controller after charging is completed.
( Lamp color : Red --> Green )
1) Power on/off & Speed Control Knob
2) Forward / Reverse Selector
4) Handpiece Connector
5) On / Charge lamp
6) Battery Charger Connector
PORTABLE MICRO MOTOR USER'S MANUAL
Features
* 30,000 RPM
* Rechargeable
* Up to 8 hours battery life
* 3.5 hours battery full charge
* Variable speed control
* Light weight handpiece
* Chuck Locking
* Easy bit change
* Uses standard
2.35mm (3/32") bits
* High torque
* Quiet operation
* No vibration
* Rechargeable battery,
clips to belt
Product Components & Part Name
Setting & Operation
● Warning for Low Voltage Battery : We recommend to charge the
battery immediately when the red light is blinking.
(It shows that the battery remains 20%)
● To protect the battery the battery is not charging
while user use the handpiece with connection DC Adaptor.
(2) Handpiece Operation
a.
Connect Handpiece Cord to the jack marked as "MOTOR"
(DC Motor Connector)in the front of the controller.
b.
Turn the Speed Control Knob to start the handpiece. Turn it until click
sound to power off and to stop the handpiece.
c.
Turn the Forward/Reverse Selector to "FWD" to run the
motor in the forward direction, or to "REV" to run it in the
Reverse direction.
d.
Handpiece Motor speed can be varied between 0 and 30,000 rpm
by the Speed Control Knob
(3) Insertion and removal of bits
Turn the handle in the counter-clock direction until the click sound to
open the chuck.
The chuck is opened and the bit is removed.
Turn the handle in clock direction until the end and the chuck is closed
and the bit is locked.
adaptor
Input : 100-240V~ 47-63Hz 0.9-0.34A
Output : 30V 1A max
Handpiece (POHP)
Rotation (r.p.m) : 0~30,000rpm
Dimensions : φ19 x L135(mm)
Weight : 172g
Contorller
Input : 30V 1A
Output : 24V 1A
Size : 65(W) x 129(D) x 36(H)
Weight : 388g
Thank you for your purchase.
Maintain and repair properly in order to have trouble-free performance for many years
Please keep this manual for future reference.
Saeshin is not responsible for the accident causing by not following the instructions.
The appearance and specification may be changed without any further notices.
Users are responsible for the operation and maintenance.
By informing the product, model, faulty status, the kind consulting
and quick service will be provided.
Specifications
1. Do not work in a dangerous place. Do not use the control box in a humid place,
use in a proper place.
2. Environment setup
Temperature : +10℃~+40℃ Humidity : 30%~75% Air Pressure: 700~1060hPa
3. Our handpiece and foot pedal should be only used for our control unit.
4. Bit
- Dimensions of the Bit: 2.35mm(ISO7785-2 TYPE2)
- Minimum fitting length of Bit: 10mm
- When locked in the chuck, the maximum projection length of Bit should be
less than 35mm.
- Use the bit that conforms to the ISO standard. Avoid using a rusty or bent bit
that cause excessive wear of bearings.
- Keep safe speed and precautions recommended by bit manufacturer.
[the allowable RPM according to the bar diameter]
Please keep the RPM according to below diagram against accident.
5. Check for any troubles, including vibration of bit, at low speed,
and then try high speed.
6. Operate the speed control dial in control box softly.
7. Turn off the power. When the handpiece
absolutely stops, screw handle in order to
change the bit.
8. Be careful not to drop the handpiece as
it may be damaged or broken.
- This may cause bearings damaged.
- In case that it is dropped, check if the bit is
bent or that any noisy of bearings and any excessive heat are generated
while carefully operating it.
CAUTION
Caution
- This equipment and accessories are to be disposed of safely
after the life span of them and national regulation must be observed.
- This equipment and accessories are to be disposed according
to the instructions given by national regulations or ask a
specialized waste service company to dispose of it.
- Follow local governing ordinances and recycling plans
regarding disposal or recycling of device components
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncon-
trolled waste disposal, please separate this from other types of wastes and
recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
E-type motor (PEHP)
Rotation (r.p.m) : 0~30,000rpm
Dimensions : φ20 x L100(mm)
Weight : 120g
A.
Contorller
B.
Handpiece - Optional
C.
E-type motor - Optional
D.
Power cord
E.
Adaptor
F.
Handpiece holder
G.
Contorller holder
H.
Bolt
I.
Handpiece stand (option)
C
E
F
G
H
I
