Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 76 / 103

137

UniqUe service ProcedUres

138

139

Fuel System Service: Fuel Injector Service

NOTE: Use proper cleanliness practices

while servicing the fuel system!

NOTE: Follow the proper sercive procedures while servicing

the fuel system and always use the correct torque!

• Proper torque is crucial with the 6.4L Power

Stroke

Diesel’s high pressure fuel system.

• When replacing fuel injectors, always follow the

correct procedure for installation and torque.

• Always use proper protective fuel system

caps whenever a tube is removed.

• Avoid cleaning parts near fuel system components.

• Tool # 310-158 (fuel caps)

Fuel System Service: Fuel Injector Lubrication

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• Always replace the O-ring and the steel gasket at the

tip of the injector when reinstalling an injector. New

injectors come with these items already installed.

• Always lightly lubricate the new O-ring with

clean engine oil prior to assembly.

Fuel System Service: Removing

and Installing Injector Gasket

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• To remove the gasket, use a razor blade to get between the

gasket and injector body, then slowly work the gasket off.

• To install the new gasket, use a 9mm 12 point

deep well socket and press the gasket on

by hand making sure it is fully seated.

• Make sure the gasket is installed correctly.

The raised portion of the gasket should be

facing away from the injector body.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды