Ford 6.4L Power Stroke Скачать руководство пользователя страница 26

Страница: 26 / 103

Lubrication SyStem

Front Cover

• Oil flows from the crankcase to the oil pump

via a passage through the upper oil pan,

front cover, and oil pump housing.

• When the oil pump is turned by the crankshaft it creates oil

flow and pushes oil through two passages. One passage

is to the oil cooler and the other is through the oil pressure

regulator then to the oil pump inlet (this passage is only

used when pressure exceeds 65 psi). When the oil reaches

the numerous restrictions throughout the engine, pressure

is then created (pressure is the resistance to flow).

• All of the passages from the front cover to the crankcase

are sealed with a rubber coated metal, one piece gasket.

Oil Filter Base

• The oil filter base contains the mounting provisions

for the oil filter housing and the oil filter stand pipe

(which contains the oil filter bypass valve).

• Inside the oil filter housing, there are the following

valves: Inlet/Anti drainback valve, oil cooler

bypass valve, and the oil filter drain valve.

• The oil filter base also contains the ports for the EOT, EOP,

and turbocharger oil supply. These ports are all connected

with the cooled/filtered oil passage directly beneath them.

Oil Cooler Cover

• The oil cooler cover has passages in it to

direct the flow of coolant and oil.

• Oil is routed from the front of the crankcase to the

rear of the housing where it enters the oil cooler. The

oil passes from the rear of the oil cooler to the front of

the cooler and is cooled in the process. The oil is then

sent to the oil filter through the oil filter base. Filtered

oil is sent to the oil passages in the crankcase, the

turbocharger supply line, and the EOT/EOP sensors.

• The coolant is directed from the front of the crankcase

to the front of the oil cooler. It then passes through the

oil cooler and cools the oil. As the coolant exits the front

of the cooler it is directed down into the coolant stream

where it re-enters the crankcase cooling system.

Note: If the oil cooler is damaged it could cause

contamination of the lubrication and cooling systems.

Coolant Into
Cooler

Coolant From WaterPump

Right Oil Supply

Left Oil Supply

Coolant out
from Cooler

Coolant Back
to Block

Oil from
Cooler

Oil into
Cooler

Oil From
Pump

Oil Filter
Drain

EOP

EOT

Oil Cooler Bypass

Turbocharger
Oil Feed

Inlet/Anti Drain Back

Oil Filter Drain

Supply to Engine
(clean oil from
filter)

One Piece Gasket

Oil Pump Outlet/Oil Cooler Supply

Oil Pump Inlet

Diagnostic Port

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды