Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 46 / 103

Piezo Electric Fuel Injector

• Piezo Electrically Actuated

• High Electrical Effeciency

• High Voltage Supply

• Up to 5 Injections Per Combustion Event

• Self extracting hold down clamp

Fuel ManageMent SySteM

Fuel Injector Features

• The injector uses a Piezo Actuator to electrically

control the injections with extreme precision.

• The Piezo Actuator is turned on for approximately 0-400

µs (micro second or millionth of a second) for 2 injections.

• No special tools are needed to remove the injectors from

their bore. The injector is slowly removed from its bore

by removing the self-extracting hold down clamp bolt.

Injector & O-ring

• The injector has one (1) replaceable o-ring on the

outside of the body, and one (1) replaceable soft

steel combustion gasket on the tip of the injector.

• The injector’s piezo actuator has a single two (2) pin

connector that is located under the valve cover.

• The fuel charging harness has a single main connection

point at the front of the valve cover spacer.

Piezo Actuator

• The piezo actuator is an electrically energized device that

acts similar to a solenoid but is much more precise.

• A piezo actuator is a composition of piezo discs, that

when electrically energized, cause the discs to deform

resulting in an expansion. This expansion results in

a longitudinal motion thus controlling the injector.

• When energized, the piezo actuator pushes downward

against the valve piston. The piezo actuator is returned

to its non energized state via the ECM switching

the polarity of the electrical feed to the injector.

Fuel Inlet
From High
Pressure Fuel Rail

Piezo Actuator

O-Ring

Fuel Return Line
Drain Holes

Soft Steel
Combustion Gasket

Piezo Actuator
(non-energized)

Electrical
Connector

Piezo Actuator
(energized)

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды