Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 15 / 103

6.4L POWER STROKE

DIESEL OvERvIEW

High Pressure Common Rail Fuel System

• The 6.4L Power Stroke Diesel engine uses a

high pressure fuel injection pump to deliver fuel

to each piezo electric fuel injector via a high

pressure common fuel rail, one rail per bank.

Cylinder Head & Head Bolts

• The 6.4L Power Stroke Diesel uses a four (4) valve per

cylinder head design to optimize airflow and efficiency.

• The 6.4L Power Stroke Diesel engine uses larger head bolts

than the 6.0L Power Stroke Diesel engine (M16 vs M14).

• The 6.4L head bolts are also slightly shorter than the

6.0L head bolts. The 6.4L head bolts do not retain

the rocker carrier like the 6.0L head bolts do.

Intake Valves

Exhaust Valves

Injector Nozzle

Glow Plug

Fulcrum Plate & Rocker Arms

• The fulcrum plate, which holds the rocker

arms, is bolted to the rocker pedestal.

• The two (2) bolts that secure the fulcrum plate pass

through the fulcrum plate and the rocker pedestal

and are then secured into the cylinder head.

6.4L (M16)

6.0L (M14)

Fulcrum Plate

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды