Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 77 / 103

140

UniqUe service ProcedUres

141

142

Turbocharger Lifting Bracket

• Anytime removal or installation of the turbocharger

is performed, always use the turbocharger

lifting bracket to ensure proper engagement and

disengagement of the turbocharger drain tubes.

• The tool is designed to balance the turbochargers

and hold the two turbine housings in alignment.

• Tool # 303-1266

Checking Fuel Pressure

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• There is a fuel return presure test valve (schrader) located

on the front of the fuel cooler on the left side of the engine.

• Proper fuel pressure is very important. Too much

or too little pressure could be detrimental.

• Follow the proper procedure for checking fuel

pressure and make sure the correct specification

for supply pressure is achieved.

NOTE: Supply pressure needs to be checked at the

horizontal fuel conditioning module (HFCM) outlet.

Test Port (return pressure)

Turbocharger Assembly Tool

• The series sequential turbocharger is comprised

of two turbochargers, low pressue turbocharger

and high pressure turbocharger. When assembling

these two turbochargers together, always use the

turbocharger assembly tool shown at right.

• Tool # 303-1269

• Follow the proper assembly procedure.

• The turbocharger assembly tool is necessary

to ensure that proper alignment/engagement

of the two turbochargers is achieved.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды