Ford 6.4L Power Stroke Скачать руководство пользователя страница 79

Страница: 79 / 103

146

UniqUe service ProcedUres

147

148

Cutting T-Joints: Rear Cover

• The T joint is where the bedplate gasket is

bonded to the rear cover. This bond must be

cut prior to removing the rear cover.

• After you loosen all of the bolts you can slide a

cutting tool between the block/bedplate and the

rear cover to sever the bonding compound.

NOTE: Failure to cut the T joint will stretch the

bedplate gasket and result in an oil leak!

High Pressure Fuel Injection Pump: Gear Service

NOTE: Use proper cleanliness practices

while servicing the fuel system!

NOTE: Severe engine damage can

occur if installed incorrectly!

• It is possible to tighten the gear on the high pressure

fuel injection pump with the gear backwards. The gear

and shaft both have a taper that needs to match.

• If you tighten the gear with it backwards the

tapers will not be aligned but the bolt will

start providing a means of tightening.

• Please pay special attention to insure that the gear is

installed correctly with the tapers on both the gear and

the high pressure fuel injection pump shaft aligned.

Incorrect

Correct

Cutting T-Joints: Front Cover

• The T joint is where the bedplate gasket is

bonded to the front cover. This bond must be

cut prior to removing the front cover.

• After you loosen all of the bolts you can slide a

cutting tool between the block/bedplate and the

front cover to sever the bonding compound.

NOTE: Failure to cut the T joint will stretch the

bedplate gasket and result in an oil leak!

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды