Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 99 / 103

diagnostic codes

- Self Test - Key On Engine Off

- Key On Engine Running

- Continuous Operation

REGEN

- Test Follows a REGEN CYCLE

SHUT DOWN

- Test Follows Key Off

- Test Operates at Key On

1PC

- Once Per Cycle

DATA Color Code

MIL For Both F250/F350 and F450/F550

MIL For Only F250/F350

MIL For F250/F350 and Wrench for F450/F550

Wrench for Both F250/F350 and F450/F550

No MIL or Wrench Light

DTC

How Set

Code Description

Brief Description

Software Parameters

Required to Set Code

Service Instructions /

Part Replaced

O R C

P0676

Cylinder 6 Glow Plug Circuit

This error occurs if the current for an individual glowplug

is either lower than the minimum current threshold

or higher than the maximum current threshold.

An open is a current level less

than 4 amps and a shorted

current level is above 60 amps.
Glow Plug on time > 8.5 sec

Wiring, Glow Plug, GPCM

P0677

Cylinder 7 Glow Plug Circuit

This error occurs if the current for an individual glowplug

is either lower than the minimum current threshold

or higher than the maximum current threshold.

An open is a current level less

than 4 amps and a shorted

current level is above 60 amps.
Glow Plug on time > 8.5 sec

Wiring, Glow Plug, GPCM

P0678

Cylinder 8 Glow Plug Circuit

This error occurs if the current for an individual glowplug

is either lower than the minimum current threshold

or higher than the maximum current threshold.

An open is a current level less

than 4 amps and a shorted

current level is above 60 amps.
Glow Plug on time > 8.5 sec

Wiring, Glow Plug, GPCM

P0684

Glow Plug Control Module

to PCM Communication

Circuit Range/Performance

This error occurs when the pass/fail status information

signal, sent by the GPCM to the PCM, is consistantly high,

consistantly low, or the period of the signal is out of range.

GP active >5 sec

Wiring, GPCM, PCM

P0691

Fan 1 Control Circuit Low

P0692

Fan 1 Control Circuit High

P0703

Brake Switch B Input Circuit

This error occurs when the brake switch is

not activated during the KOER self test.

P1000

RESET

OBD Systems Readiness

Test Not Complete

This error occurs when all other DTC’s have been

erased from the system. This error will subside

when all OBD monitors have been completed.

P1102

Mass Air Flow Sensor In Range

But Lower Than Expected

This error occurs when the measured value of

mass air flow is lower than a threshold value

for a predetermined period of time.

0%< EGR Position < 50%
Engine speed >700 rpm < 2400 rpm
based on a table > 30sec

Wiring, MAF assembly, PCM

P1103

Mass Air Flow Sensor In Range

But Higher Than Expected

This error occurs when the measured value of

mass air flow is higher than a threshold value

for a predetermined period of time.

0%< EGR Position < 50%
Engine speed >700 rpm < 2400 rpm
based on a table > 30sec

Wiring, MAF assembly, PCM

P115A

Low Fuel Level - Forced

Limited Power

This error occurs when the PCM recieves a signal

indicating that the vehicle is critically low on fuel.

P117B

Exhaust Gas Temperature

Sensor Correlation

This error occurs when the three exhaust temperature

sensor readings are not within a specified temperature

range when compared to one another.

P117F

Fuel Pressure Regulator

Excessive Variation

This error occurs when any of the fuel pressure

corrections either become less than a minimum

threshold or more than a maximum threshold.

Low pressure fuel system,

injector leakage

P1184

Engine Oil Temperature Sensor

Out Of Self Test Range

This error occurs when the KOER self test is attempted but the

engine has not reached an operating temperature of 60º C.

EOT < 60 >205deg C

P120F

Fuel Pressure Regulator

Excessive Variation

This error occurs when the difference between actual rail

pressure and the PCM’s calculated setpoint is large, and the

actual fuel pressure crosses the setpoint too frequently.

Wiring to FUP sensor,

FUP sensor, low pressure

fuel system

P127A

Aborted KOER - Fuel

Pressure Failure

This error occurs when fuel pressure does not

rise sufficiently during the KOER self test.

Cannot achieve or return to 53

FUP_SP. Cannot achieve 139MPa

P132A

Turbocharger Boost

Control A Electrical

This error occurs if the turbocharger cannot perform

a sweep/learn of the min/max position.

P132B

Turbocharger/Supercharger

Boost Control A Performance

This error occurs if a fault is detected

within the turbocharger actuator.

Internal to the turbocharger

control module

Wiring, SRA module,PCM

P132C

Turbocharger/Supercharger

Boost Control A Voltage

This error occurs when the voltage to the

turbocharger actuator is below the threshold

for a predetermined period of time.

Internal to the turbocharger

control module

Wiring, SRA module,PCM

P1335

EGR Position Sensor Minimum/

Maximum Stop Performance

This error occurs when voltage of the EGR valve

falls below the minimum threshold.

1.3v >2.5sec

Wiring, EGR valve

assembly,PCM

P1336

Crankshaft/Camshaft Sensor

Range/Performance

This error occurs when the reference gap of the crankshaft

trigger wheel is not detected at the correct position.

Internal to the engine control module

System error, electrical

noise,…

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды