Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 74 / 103

131

UniqUe service ProcedUres

132

133

Oil Filter: Replacement

• First loosen the oil filter cap which will open

the oil filter drain and allow the oil from the

filter housing to drain into the crankcase.

• Drain the oil from the oil pan.

• After all of the oil has drained from the oil pan remove

the oil filter and discard it in the appropriate location.

• Install the new oil filter element and tighten

the oil filter cap to the recommended torque.

This will close the oil filter drain.

• Refill crankcase with the correct

volume of recommended oil.

Note: The oil filter snaps into the oil filter lid.

Fuel Filter: Replacement

NOTE: Use proper cleanliness practices while servicing

the fuel system, do not let any dirt get into the housing!

• Clean all dirt and debris from the engine mounted

fuel filter lid thoroughly. Make sure your hands

and any tools involved are clean also!

• Remove the fuel filter lid and lift the filter element out

of the housing and discard in the appropriate location.

• To avoid fuel spills, use a suction gun or similar device to

remove the remaining fuel from the fuel filter housing.

• Install the new filter and tighten the fuel

filter lid to the specified torque.

NOTE: Before starting the vehicle, turn the key

to the on position for 30 seconds, then key off.

Do this 6 times to ensure the fuel filter housing

is full of fuel before starting the vehicle.

Fuel System Service Cleanliness:

Fuel Injectors, Fuel Rail

NOTE: Use proper cleanliness practices

while servicing the fuel system!

• Always use fuel system caps when servicing

the fuel injectors or replacing fuel lines.

• Do not have the fuel system open to the elements any

longer than is necessary to perform the job at hand.

• Tool # 310-158 (fuel caps)

Fuel Rail Caps

Fuel Injector Caps

Fuel Filter Lid

Fuel Filter Element

Oil Filter Lid

Oil Filter Element

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды