Ford 6.4L Power Stroke Скачать руководство пользователя страница 48

Страница: 48 / 103

Two Stages of Injection

• Main Injection

• End of Main Injection

Fuel ManageMent SySteM

Stages of Injection

• The injection cycle has two (2) stages.

• Main injection.

• End of main injection.

• This injection system is capable of performing both steps

of the injection cycle up to 5 times per firing cycle.

Pre-Main Injection

• The piezo electric fuel injector is constantly being filled

with fuel via the high pressure fuel injection pump.

• High pressure fuel from the high pressure fuel

injection pump enters the following areas:

- control piston chamber (2).

- spring side of the valve mushroom (4).

- high pressure chamber (3).

• The needle control spring (9) holds the needle on its seat

so that fuel cannot enter the combustion chamber.

• The piezo actuator (1) is in a non-energized state.

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды