Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 24 / 103

Lubrication SyStem

Pick-up Tube / Oil Aeration

• The pick-up tube supplies oil from

the oil pan to the oil pump.

• The pick-up tube is sealed to the upper oil pan

utilizing an o-ring. If the o-ring is damaged

or missing, it could cause oil aeration.

Oil Pressure Regulator

• The oil pressure regulator is located in the gerotor

housing just to the right (when looking at the

engine from the front) of the gerotor oil pump.

• The oil pressure regulator is calibrated to

open at pressures above 65 psi. It should

be closed below that pressure.

• The regulator valve utilizes a force, provided via the

regulator spring, to apply a pressure equal to 65

psi. Whenever oil pressure exceeds this force, the

regulator valve will move downward and allow the

excess pressure to bleed off back through a passage

that routes the oil back to the inlet side of the pump.

Gerotor Oil Pump

• The gerotor oil pump is driven off of the

flats on the nose of the crankshaft.

• The gerotor oil pump and regulator valve are

held in their own removeable housing.

Alignment Dowels

Inner Gear

Outer Gear

Dowel Locations

Upper Oil Pan

Pick-up Tube

Oil Pump

Oil Pressure Regulator

Regulator
Housing

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды