83
special torque chart (reference only)
STANDARD TORQUE CHART
Hex Flange Head
Thread
Torque
Torque
Wrench
Diameter
Nm
Size (mm)
M6 x 1
114 lbf/in
13
8
M8 x 1.25
23 lbf/ft
31
10
M10 x 1.5
45 lbf/ft
62
13
M12 x 1.75
79 lbf/ft
107
15
M14 x 2
127 lbf/ft
172
M15 x 2
159 lbf/ft
216
M16 x 2
196 lbf/ft
266
21
Torque Chart Notes
1) Lightly coat o-ring with clean engine prior to install.
2) Apply threadlock 262 to bolt threads prior to install.
3) Do not reuse. These bolts are one time stretch to yield.
4) Do not reuse exhuast manifold bolts and studbolts.
COMPONENT
STANDARD
METRIC
Glow plug
124 lbf/in
14 Nm
Glow plug control module bolts and nuts (GPCM)
114 lbf/in
13 Nm
High pressure common rail (HPCR) mounting bolts
23 lbf/ft
31 Nm
High pressure common rail (HPCR) to fuel injector tubes
Figure G, I
Figure G, I
High pressure fuel injection pump & pump-to-rail tube installation
Figure H
Figure H
High pressure fuel injection pump cover mounting bolts
114 lbf/in
13 Nm
High pressure fuel injection pump drive gear bolt
57 lbf/ft
78 Nm
High pressure fuel injection pump mounting bolts
45 lbf/ft
62 Nm
High pressure fuel tube nuts (all)
144 lbf/in
30 Nm
Intake manifold pressure sensor (MAP)
106 lbf/in
12 Nm
Intake air temperature 2 (IAT2) sensor
124 lbf/in
14 Nm
Intake manifold bolts and stud bolts
Figure D
Figure D
Lifting eye bolts
45 lbf/ft
62 Nm
Oil cooler to crankcase mounting bolts (M8)
23 lbf/ft
31 Nm
Oil filter base to cooler cover screws (M6 thread forming)
89 lbf/in
10 Nm
Oil filter cap
18 lbf/ft
25 Nm
Oil filter housing to filter base bolts
16 lbf/ft
22 Nm
Oil filter stand pipe bolt (M5 thread forming) W/new oil cooler
61 lbf/in
7 Nm
Oil filter stand pipe bolt (M5 thread forming) reusing existing oil cooler
30 lbf/in
3 Nm
Oil pan bolt - lower pan
114 lbf/in
13 Nm
Oil pan bolt - upper pan
114 lbf/in
13 Nm
Oil pan drain plug (see note 1)
32 lbf/ft
44 Nm
Oil pickup tube bolts
114 lbf/in
13 Nm
Oil pump housing bolts
16 lbf/ft
22 Nm
Oil pressure regulator plug
26 lbf/ft
35 Nm
Piston cooling jet mounting bolts (see note 2)
114 lbf/in
13 Nm
Rocker arm assembly bolts
Figure J
Figure J
Rear cover M10 (manual only)
45 lbf/ft
62 Nm
Rear cover M8 (man & auto)
23 lbf/ft
31 Nm
Thermostat housing hold down plate bolts
114 lbf/in
13 Nm
Turbocharger actuator mounting bolt
168 lbf/in
19 Nm
Turbocharger air inlet duct clamp
44lbf/in
5 Nm
Turbocharger pedestal bolts
45 lbf/ft
62 Nm
Turbocharger to pedestal bolts
148 lbf/ft
201 Nm
Turbocharger crossover tube support mounting
79 lbf/in
9 Nm
Turbocharger heat shield bolts
96 lbf/in
11 Nm
Turbocharger oil supply banjo bolts (M12)
28 lbf/ft
38 Nm
Turbocharger oil supply standoff fittings to center housings
35 lbf/ft
47 Nm
Turbocharger oil supply tube retaining bolt to oil cooler
114 lbf/in
13 Nm
Valve cover base bolts
114 lbf/in
13 Nm
Valve cover bolts and studs
80 lbf/in
9 Nm
Vibration damper bolts (note 3) (only use new bolts)
Figure E
Figure E
Содержание 6.4L Power Stroke
