Ford 6.4L Power Stroke Скачать руководство пользователя

Страница: 70 / 103

123

ElEctrical componEnts

124

125

Exhaust Gas Recirculation Valve (EGR Valve)

• The EGR valve is used to mix cooled exhaust gases

with intake air to lower emissions and noise.

• The EGR valve is stepper motor controlled

• The valve is powered in both the open and close directions.

Turbocharger Actuator

• The turbocharger actuator is an electronic motor

that controls the position of the vanes inside of the

high pressure turbocharger’s turbine housing.

• The turbocharger actuator is mounted directly to the

high pressure turbo and is connected to the vanes

inside the turbine housing by a control arm.

Throttle Body

• The throttle body is operated by a stepper

motor controlled by the ECM and assists with

the exhaust aftertreatment system.

Turbocharger
Actuator

Control Arm

Throttle Body

Содержание 6.4L Power Stroke








































































































Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды

Ford 6.4L Power Stroke, Руководство пользователя

Результаты поиска

Содержание 6.4L Power Stroke

Отзывы:

Похожие инструкции для 6.4L Power Stroke

Бренды по названию

Популярные бренды