DTM Print CX86e Скачать руководство пользователя страница 150

Страница: 150 / 214

150

Message

Description

CHECK IMAGE DRUM AND TONER CARTRIDGE

546:TONER CARTRIDGE MISSING

An error has occurred in the toner cartridge. Remove the toner car-

tridge, and set it again.

IMAGE DRUM MISSING

342:ERROR

The image drum unit is not set correctly. Set the image drum unit-

again.

CHECK FUSER UNIT

[ERRCODE]:FUSER UNIT MISSING

The fuser unit is not set correctly. Set the fuser unit again.

CLOSE [COVER]

[ERRCODE]:[COVER] OPEN

The displayed cover is open. Close the cover.

ERRCODE 310: Top cover

ERRCODE 589: Feeder cover

CLOSE TONER REPLACEMENT COVER

586:TONER COVER OPEN

The toner replacement cover is open. Close the toner replacement

cover.

WAIT A MOMENT

REBOOTING [%CODE%]

The machine is restarting. Wait until the machine restarts.

SHUTTING DOWN. PLEASE WAIT

TURN OFF AUTOMATICALLY

The machine is shutting down. Wait until the power turns off.

TURN OFF POWER

SHUTDOWN COMPLETED

The shutdown process of the machine is complete. Turn the machine

off.

POWER OFF/ON

[ERRCODE]:ERROR

A critical error has occurred in the machine. Turn the machine off and

then on again. If the machine does not recover, contact your dealer.

Connection Problems

Network Connection Problems

Cause

Remedy

Reference

A cross cable is being used.

A cross cable is being used. Use a straight

cable.

The machine was turned on before

connecting the cable.

Turn the machine on after connecting the

cable.

Connecting a LAN Cable

There is a compatibility problem with

the hub.

Select the correct connection in [ADMIN

MENU] > [NETWORK SETUP] > [HUB LINK

SETTING] of the menu.

The network connection settings are

not suitable.

To connect to a wired network, set

[WIRED] to [Enabled] for the network

connection.

Connecting a LAN Cable

Using Both a Wired LAN and Wireless LAN

Connection

The IP addresses are incorrect.

Check whether the IP address of the

machine matches the IP address of the

machine set in the computer.
Check whether the IP address is the same

as another device.
Check whether the IP address, subnet

mask, and gateway address are correct.

Checking Information About the Machine

Содержание CX86e






















































































































































































































Результаты поиска

Содержание CX86e

Отзывы:

Похожие инструкции для CX86e

Бренды по названию

Популярные бренды

DTM Print CX86e, Руководство пользователя

Результаты поиска

Содержание CX86e

Отзывы:

Похожие инструкции для CX86e

Бренды по названию

Популярные бренды